SeaMaker Engine Driven Water Maker Model and Pricing

                     Model   Fresh Water Production GPH/GPD  Boost Pump 
    Amps
    12VDC 
     Price  
     SM25ES 25/600 5 $4300
     SM25E 25/600 5  $4695
    SM45ES 45/1080 5  $5205
     SM45E 45/1080  5   $5600 

    * The SeaMaker Simple water makers (SM25ES and SM45ES) do not include the standard remote control panel and mount the system controls on the end of the RO Pressure Vessel



    Module 1: High Pressure Pump and Clutch Assembly

    One General Pump Company triplex plunger pump with a 316 stainless steel manifold and wetted parts, solid ceramic plungers and an anodized aluminum crankcase mechanically coupled to a dual v-belt electrically engaged clutch.  Fitted with a pressure relief valve preset to 950 PSI.  

    Module 2 (SM25E): RO Pressure Vessel Assembly

    One filament wound fiberglass/epoxy pressure vessel
    OneDow Filmtec Polyamide thin-film composite high salt rejection RO Membrane
    Two Stainless Steel clamps affixed to fiberglass mounting feet.
    One 3ft long 3/8" high pressure braided stainless steel silicone covered hose for connecting the high pressure pump outlet to the RO pressure vessel.  (Longer hose available upon request for an additional charge)

    Module 2 (SM45E): RO Pressure Vessel Assembly

    Two filament wound fiberglass/epoxy pressure vessel
    Two Dow Filmtec Polyamide thin-film composite high salt rejection RO Membrane
    Four Stainless Steel clamps affixed to fiberglass mounting feet.
    One 3ft long 3/8" high pressure braided stainless steel silicone covered hose for connecting the high pressure pump outlet to the RO pressure vessel.  (Longer hose available upon request for an additional charge)

    Module 3: Pre-filter and Boost Pump Assembly

    Two 10” clear filter housings with mounting bracket
    One 20 micron pre-filter element
    One 5 micron pre-filter element
    One12V DC Jabsco centrifugal boost pump

    Module 4:
    Valving and Cleaning Assembly

    One clear filter housing with mounting bracket
    One activated carbon filter element
    Two 3-way valves for selecting: normal operation of inlet seawater, fresh water rinse from ships tanks, or pickling solution
     
    Module 5
    : Remote Control Panel 
    (Not included with the SeaMaker Simple units)

    An anodized aluminum panel with the following system controls:
    One 0-1 GPM flow meter
    One 0-1500 pressure gauge
    One stainless steel product water selector 3-way valve
    One stainless steel pressure regulating needle valve
    One 12VDC boost pump electrical switch
    One 12VDC High Pressure clutch switch
    One 5ft 3/8" high pressure braided stainless steel silicon coated hose (Longer hose available upon request for an additional charge)

    Miscellaneous Included Equipment & Supplies:

    30ft of green 1/2" Polyethylene sea water tubing
    30ft of blue 1/4" Polyethylene product water tubing
    30ft of red 1/4" Polyethylene brine water tubing
    One cutter for the water tubing
    One spacing tool for proper insertion and removal of water tubing into push connector
    One 1/2" male NPT to push connector fitting for connecting to your seawater inlet source
    One 1/2" male NPT to push connector fitting for connecting to your ships water system for fresh water flushing of the water maker
    Three 1/4" male NPT to push connector fittings for connecting the brine, product water, and sample water outlet lines to your ships plumbing
    Locking clips for all push connector fittings
    Electronic copy of the Installation, Operation and Maintenance manual
    One filter housing wrench for filter element replacement
    5 pounds of pickling reagent
    One hand-held TDS meter for checking water quality
    Four spare 1/2" male NPT 90° elbow to push connector fitting if needed to replace the straight fittings which are pre-mounted on the modules for making the system plumbing easier
    An assortment of push-to-connect fittings to aid in installation

    What we Don't Provide

    Raw water through hull
    Raw water sea strainer (we recommend one like this)
    Electrical installation wire and breakers for the AC and DC Pumps
    Mounting screws and bolts for the individual system Modules
    Zip ties and mounting straps for securing the electrical and water lines


    Water Maker Module Sizes:

    The below table provides the length, width, height, and weight of the various system modules.  The listed dimensions represent the greatest size measurement to create a box that the module can be contained within, however as can be seen in the module photo images, the modules could actually fit into a smaller space depending upon the installation orientation.

          Module    Length
    (inches) 
    Width
    (inches)
    Height
    (inches) 
     Weight
    (pounds) 
     1: Pump and Clutch  ~~
     ~~  ~~ ~~
     2 (SM25): RO Pressure Vessel   44
    6.5   14  
     2 (SM45): RO Pressure Vessel 44 12 6.5 25
     3: Prefilter Assembly
    11.5
    5
    14.5
    6.5
      3: 12VDC Boost Pump
     6.4 4.5
    3.7
    5.3
      4: Valving and Cleaning Assembly 
    13.5
     5  14.5  5
       5: Remote Control Panel  7.5 5
    (depth)
     
    10.75   4
    Optional
      Valving & Cleaning Panel ($350)

    6.25
    5
    (depth)

    10.75 
    5



    We put together the Cruising Consumable Kit with everything you will need to cut the dock lines and head out cruising for a year or more for $165.
    • 20 and 5 micron pre-filters
    • Pickling reagent
    • Activated carbon filters
    • High pressure pump crank case oil

    ***
    The SeaMaker Simple line  (SM30S, SM30S) do not come with a remote panel.  The Simple water makers simply mount the needed system controls on the RO Pressure Vessel.


    CLICK HERE

    To request a copy of the SeaMaker Engine Driven water maker manual with technical specifications along with detailed installation and operation instructions.
    Or
    Call Rich 7 Days-A-Week
    to talk all things water makers.
    619-609-3432619-609-3432


    Engine Driven High Pressure Pump
    Installation Photo


    Module 1
    Pump and 12v Clutch Assembly
    (Right Hand Pump Shown)


    Module 2
    RO Pressure Vessel


    Module 3
    12VDC Centrifugal Boost Pump


    Module 3
    Prefilter Assembly
    with 20 and 5 micron Prefilters


    Module 4
    Valving and Cleaning Assembly


    Module 5
    Remote Panel


    Cruising Consumable Kit No 2


      Optional Valving and Cleaning Panel
    Replacing the two 3-Way Valves Mounted on the Valving and Cleaning Assembly ($350)