
SeaMaker Engine Driven Water Maker Model and Pricing
Model | Fresh Water Production GPH/GPD | Boost Pump Amps 12VDC | Price |
---|---|---|---|
SM25ES | 25/600 | 5 | $4305 |
SM25E | 25/600 | 5 | $4700 |
SM45ES | 45/1080 | 5 | $5455 |
SM45E | 45/1080 | 5 | $5850 |
* The SeaMaker Simple water makers (SM25ES and SM45ES) do not include the standard remote control panel and mount the system controls on the end of the RO Pressure Vessel
Module 1: High Pressure Pump and Clutch Assembly
One General Pump Company triplex plunger pump with a 316 stainless steel manifold and wetted parts, solid ceramic plungers and an anodized aluminum crankcase mechanically coupled to a dual v-belt electrically engaged clutch. Fitted with a pressure relief valve preset to 950 PSI.
Module 2 (SM25E): RO Pressure Vessel Assembly
One filament wound fiberglass/epoxy pressure vessel
OneDow Filmtec Polyamide thin-film composite high salt rejection RO Membrane
Two Stainless Steel clamps affixed to fiberglass mounting feet.
One 3ft long 3/8″ high pressure braided stainless steel silicone covered hose for connecting the high pressure pump outlet to the RO pressure vessel. (Longer hose available upon request for an additional charge)
Module 2 (SM45E): RO Pressure Vessel Assembly
Two filament wound fiberglass/epoxy pressure vessel
Two Dow Filmtec Polyamide thin-film composite high salt rejection RO Membrane
Four Stainless Steel clamps affixed to fiberglass mounting feet.
One 3ft long 3/8″ high pressure braided stainless steel silicone covered hose for connecting the high pressure pump outlet to the RO pressure vessel. (Longer hose available upon request for an additional charge)
Module 3: Pre-filter and Boost Pump Assembly
Two 10” clear filter housings with mounting bracket
One 20 micron pre-filter element
One 5 micron pre-filter element
One12V DC Jabsco centrifugal boost pump
Module 4: Valving and Cleaning Assembly
One clear filter housing with mounting bracket
One activated carbon filter element
Two 3-way valves for selecting: normal operation of inlet seawater, fresh water rinse from ships tanks, or pickling solution
Module 5: Remote Control Panel
(Not included with the SeaMaker Simple units)
An anodized aluminum panel with the following system controls:
One 0-1 GPM flow meter
One 0-1500 pressure gauge
One stainless steel product water selector 3-way valve
One stainless steel pressure regulating needle valve
One 12VDC boost pump electrical switch
One 12VDC High Pressure clutch switch
One 5ft 3/8″ high pressure braided stainless steel silicon coated hose (Longer hose available upon request for an additional charge)
Miscellaneous Included Equipment & Supplies:
30ft of green 1/2″ Polyethylene sea water tubing
30ft of blue 1/4″ Polyethylene product water tubing
30ft of red 1/4″ Polyethylene brine water tubing
One cutter for the water tubing
One spacing tool for proper insertion and removal of water tubing into push connector
One 1/2″ male NPT to push connector fitting for connecting to your seawater inlet source
One 1/2″ male NPT to push connector fitting for connecting to your ships water system for fresh water flushing of the water maker
Three 1/4″ male NPT to push connector fittings for connecting the brine, product water, and sample water outlet lines to your ships plumbing
Locking clips for all push connector fittings
Electronic copy of the Installation, Operation and Maintenance manual
One filter housing wrench for filter element replacement
5 pounds of pickling reagent
One hand-held TDS meter for checking water quality
Four spare 1/2″ male NPT 90° elbow to push connector fitting if needed to replace the straight fittings which are pre-mounted on the modules for making the system plumbing easier
An assortment of push-to-connect fittings to aid in installation
What we Don’t Provide
Raw water through hull
Raw water sea strainer (we recommend one like this)
Electrical installation wire and breakers for the AC and DC Pumps
Mounting screws and bolts for the individual system Modules
Zip ties and mounting straps for securing the electrical and water lines
Water Maker Module Sizes:
The below table provides the length, width, height, and weight of the various system modules. The listed dimensions represent the greatest size measurement to create a box that the module can be contained within, however as can be seen in the module photo images, the modules could actually fit into a smaller space depending upon the installation orientation.
Module | Length (inches) | Width (inches) | Height (inches) | Weight (pounds) |
---|---|---|---|---|
1: Pump and Clutch | ~~ | ~~ | ~~ | ~~ |
2 (SM25): RO Pressure Vessel | 45 | 5 | 6 | 15 |
2 (SM45): RO Pressure Vessel | 45 | 10 | 6 | 30.5 |
3: Prefilter Assembly | 13.75 | 9.75 | 5 | 5.2 |
3: 12VDC Boost Pump | 6.5 | 4.5 | 4.25 | 5.3 |
4: Valving and Cleaning Assembly | 13.5 | 5 | 14.5 | 5 |
5: Remote Control Panel (Optional TDS Meter) Depth protruding from back of panel Remote Control Panel (Standard Hour Meter) Depth protruding from back of panel | 3.5 Depth 2.875 Depth | 11 11 | 11.25 11.25 | 4.75 4.5 |
Optional Automatic Fresh Water Flush ($695) | 9.75 | 8 | 4 | 3 |
Optional Valving & Cleaning Panel ($350) | 5.5 (depth) | 5 (depth) | 10.75 | 5 |
We put together the Cruising Consumable Kit with everything you will need to cut the dock lines and head out cruising for a year or more for $165.
- 20 and 5 micron pre-filters
- Pickling reagent
- Activated carbon filters
- High pressure pump crank case oil
*** The SeaMaker Simple line (SM30S, SM30S) do not come with a remote panel. The Simple water makers simply mount the needed system controls on the RO Pressure Vessel.